--- linux.orig/arch/arm/mach-orion5x/d2net-setup.c	2009-12-03 03:51:21.000000000 +0000
+++ linux/arch/arm/mach-orion5x/d2net-setup.c	2010-02-16 08:58:15.000000000 +0000
@@ -149,10 +149,7 @@
 
 /*
  * The blue front LED is wired to the CPLD and can blink in relation with the
- * SATA activity. This feature is disabled to make this LED compatible with
- * the leds-gpio driver: MPP14 and MPP15 are configured to act like output
- * GPIO's and have to stay in an active state. This is needed to set the blue
- * LED in a "fix on" state regardless of the SATA activity.
+ * SATA activity.
  *
  * The following array detail the different LED registers and the combination
  * of their possible values:
@@ -171,12 +168,11 @@
 #define D2NET_GPIO_RED_LED		6
 #define D2NET_GPIO_BLUE_LED_BLINK_CTRL	16
 #define D2NET_GPIO_BLUE_LED_OFF		23
-#define D2NET_GPIO_SATA0_ACT		14
-#define D2NET_GPIO_SATA1_ACT		15
 
 static struct gpio_led d2net_leds[] = {
 	{
-		.name = "d2net:blue:power",
+		.name = "d2net:blue:sata",
+		.default_trigger = "default-on",
 		.gpio = D2NET_GPIO_BLUE_LED_OFF,
 		.active_low = 1,
 	},
@@ -201,25 +197,22 @@
 
 static void __init d2net_gpio_leds_init(void)
 {
+	int err;
+
 	/* Configure GPIO over MPP max number. */
 	orion_gpio_set_valid(D2NET_GPIO_BLUE_LED_OFF, 1);
 
-	if (gpio_request(D2NET_GPIO_SATA0_ACT, "LED SATA0 activity") != 0)
-		return;
-	if (gpio_direction_output(D2NET_GPIO_SATA0_ACT, 1) != 0)
-		goto err_free_1;
-	if (gpio_request(D2NET_GPIO_SATA1_ACT, "LED SATA1 activity") != 0)
-		goto err_free_1;
-	if (gpio_direction_output(D2NET_GPIO_SATA1_ACT, 1) != 0)
-		goto err_free_2;
-	platform_device_register(&d2net_gpio_leds);
-	return;
+	/* Configure register blink_ctrl to allow SATA activity LED blinking. */
+	err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
+	}
+	if (err)
+		pr_err("d2net: failed to configure blue LED blink GPIO\n");
 
-err_free_2:
-	gpio_free(D2NET_GPIO_SATA1_ACT);
-err_free_1:
-	gpio_free(D2NET_GPIO_SATA0_ACT);
-	return;
+	platform_device_register(&d2net_gpio_leds);
 }
 
 /****************************************************************************
@@ -289,8 +282,8 @@
 	{ 11, MPP_UNUSED },
 	{ 12, MPP_GPIO },	/* SATA 1 power */
 	{ 13, MPP_UNUSED },
-	{ 14, MPP_GPIO },	/* SATA 0 active */
-	{ 15, MPP_GPIO },	/* SATA 1 active */
+	{ 14, MPP_SATA_LED },	/* SATA 0 active */
+	{ 15, MPP_SATA_LED },	/* SATA 1 active */
 	{ 16, MPP_GPIO },	/* Blue front LED blink control */
 	{ 17, MPP_UNUSED },
 	{ 18, MPP_GPIO },	/* Front button (0 = Released, 1 = Pushed ) */
@@ -301,6 +294,8 @@
 	/* 24: Inhibit board power off (0 = Disabled, 1 = Enabled) */
 };
 
+#define D2NET_GPIO_INHIBIT_POWER_OFF    24
+
 static void __init d2net_init(void)
 {
 	/*
@@ -333,6 +328,8 @@
 
 	i2c_register_board_info(0, d2net_i2c_devices,
 				ARRAY_SIZE(d2net_i2c_devices));
+
+	orion_gpio_set_valid(D2NET_GPIO_INHIBIT_POWER_OFF, 1);
 }
 
 /* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */