__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: DB-88F5182-LaCie LE U-Boot 1.1.4 (Feb 9 2009 - 13:15:53) Marvell version: 2.4.9 LaCie : 1.00.0001 U-Boot code: 00200000 -> 0026FFF0 BSS: -> 00283280 Soc: 88F5182 A2 (DDR2) CPU running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 32bit width [512kB@fff80000] Flash: 512 kB Addresses 4M - 0M are saved for the U-Boot usage. Mem malloc Initialization (4M - 3M): Done *** Warning - bad CRC, using default environment CPU : ARM926 (Rev 0) 88F5182 A2 streaming disabled USB 0: host mode USB 1: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] MODE AUTO-POWER START Hit any key to stop autoboot: 0 Waiting for LUMP (2) no lump receive; continuing Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found Device 1: OK Model: Hitachi HDT721010SLA360 Firm: ST6OA3AA Ser#: STF607MH3LNE7K Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Loading from IDE device 1, partition 10: Name: hdb10 Type: U-Boot ** Bad Magic Number ** Loading from IDE device 1, partition 6: Name: hdb6 Type: U-Boot Image Name: Linux-2.6.22.7 Created: 2009-03-23 16:03:10 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1778568 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 ## Booting image at 00400000 ... Image Name: Linux-2.6.22.7 Created: 2009-03-23 16:03:10 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1778568 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux.... done, booting the kernel. Linux version 2.6.22.7 (root@grp-dash) (gcc version 4.2.1) #1 Mon Mar 23 17:03:07 CET 2009 CPU: ARM926EJ-S [41069260] revision 0 (ARMv5TEJ), cr=a0053177 Machine: Feroceon Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Built 1 zonelists. Total pages: 32512 Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro boardType=mv88F5182 productType=d2Next PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB 0MB 0MB 0MB = 128MB total Memory: 126464KB available (2792K code, 185K data, 356K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 Sys Clk = 200000000, Tclk = 166666667 CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 128MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PCI0_MEM ....base e8000000, size 128MB PCI0_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB DEVICE_CS0 ....no such DEVICE_CS1 ....no such DEVICE_CS2 ....no such DEV_BOOCS ....base fff80000, size 512KB CRYPT_ENG ....base f0000000, size 64KB Marvell Development Board (LSP Version 3.0.5_NAS_GDP_p8)-- DB-88F5182-LaCie Soc: 88F5182 A2 Detected Tclk 166666667 and SysClk 200000000 Init Marvell USB port 0 => HOST Marvell USB EHCI Host controller #0: c0493600 Init Marvell USB port 1 => HOST Marvell USB EHCI Host controller #1: c0493400 PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: orion_clocksource clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered cesadev_init(c000e7a8) mvCesaInit: sessions=640, queue=64, pSram=f0000000 Use the XOR engines (acceleration) for enhancing the following functions: o RAID 5 Xor calculation o kernel memcpy o kenrel memzero o copy user to/from kernel buffers Number of XOR engines to use: 2 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Registering unionfs 2.4 (for 2.6.22.19) io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A Marvell Ethernet Driver 'mv_ethernet': o Uncached descriptors in DRAM o DRAM SW cache-coherency o TCP segmentation offload enabled o Checksum offload enabled o Marvell ethtool proc enabled o Rx desc: 128 o Tx desc: 256 o Loading network interface 'egiga0' Intergrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter scsi 1:0:0:0: Direct-Access Hitachi HDT721010SLA360 ST6O PQ: 0 ANSI: 5 sd 1:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sda: sda1 < sda5 sda6 sda7 sda8 sda9 sda10 > sda2 sd 1:0:0:0: [sda] Attached SCSI disk sd 1:0:0:0: Attached scsi generic sg0 type 0 cfi_flash_0: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 cfi_flash_0: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. ehci_marvell ehci_marvell.4523: Marvell Orion EHCI ehci_marvell ehci_marvell.4523: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.4523: irq 17, io base 0xf1050100 ehci_marvell ehci_marvell.4523: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_marvell ehci_marvell.167817: Marvell Orion EHCI ehci_marvell ehci_marvell.167817: new USB bus registered, assigned bus number 2 ehci_marvell ehci_marvell.167817: irq 12, io base 0xf10a0100 ehci_marvell ehci_marvell.167817: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected USB Universal Host Controller Interface driver v3.0 mice: PS/2 mouse device common for all mice i2c /dev entries driver md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Loading I2C based RTC driver device interface. Found TWSI-I2C with id: 0 Found I2C RTC rs5c372 @ 0x32 Freeing init memory: 356K ===INITRAMFS: =======================================INITRAMFS================================ ===INITRAMFS: Initializing filesystem ===INITRAMFS: Mounting /proc ===INITRAMFS: Mounting /sys ===INITRAMFS: Populating /dev ===INITRAMFS: Mounting /dev/pts ===INITRAMFS: Product ID = 'd2Net' ===INITRAMFS: minRaidDevices=1 ===INITRAMFS: maxRaidDevices=1 ===INITRAMFS: Waiting for the master disk to spin up ===INITRAMFS: Waiting for 1 to 1 disks to spin up ===INITRAMFS: We finally have 1 disks, updating /dev ===INITRAMFS: Found available BootFS partition: /dev/sda7 ===INITRAMFS: Mouting /dev/sda7 on /root read only kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ===INITRAMFS: Mouting virtual filesystems ===INITRAMFS: Switching to bootfs, leaving initramfs ===BOOTFS: =======================================BOOTFS================================= ===BOOTFS: Initializing filesystem ===BOOTFS: Mounting /proc mount: /etc/mtab: Read-only file system ===BOOTFS: Mounting /sys mount: /etc/mtab: Read-only file system ===BOOTFS: Populating /dev ===BOOTFS: Mounting /dev/pts mount: /etc/mtab: Read-only file system ===BOOTFS: Mounting /dev/shm mount: /etc/mtab: Read-only file system ===BOOTFS: #### Running File System Check on Snapshot Partition (/dev/sda9) ### e2fsck 1.37 (21-Mar-2005) /dev/sda9: recovering journal /dev/sda9: clean, 12985/84480 files, 61789/168674 blocks #### Starting PatchManager using /dev/sda8 and /dev/sda9 #### kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda9, internal journal EXT3-fs: mounted filesystem with ordered data mode. ===BOOTFS: Creating base union /var/base from /var/original ===BOOTFS: Loading snapshots from /snapshots/snaps unionfs: unionfs: new generation number 2 mount: /etc/mtab: Read-only file system unionfs: unionfs: new generation number 3 mount: /etc/mtab: Read-only file system Next Generation Init version ( 0.6.10.2 Die bugs die! ) http://www.initng.org Author: Jimmy Wennlund If you find initng useful, please consider a small donation. System is starting up! runlevel/default [starting] initial/loglevel [starting] initial/mountvirtfs [starting] initial/edconf [starting] dbus [starting] bootmisc [starting] mountfs [starting] udev/filldev [starting] udev/udevd [starting] udev/mountdev [starting] udev/set_hotplug [starting] modules [starting] hald [starting] clock [starting] dhcdbd [starting] syslogd [starting] klogd [starting] swap [starting] mountuserfs [starting] usb [starting] hostname [starting] NetworkManager [starting] NetworkManager/prepare [starting] http [starting] unionfs [starting] getty/1 [starting] crond [starting] fan_controller [starting] edconfd [starting] recovery [starting] snapshot [starting] sshd [starting] sshd/generate_keys [starting] 2% initial/loglevel [done] ( done in 35ms ) 5% initial/mountvirtfs [done] ( done in 217ms ) initial/edconf start: Mounting /oldroot/snapshots/EDMINI 8% udev/mountdev [done] ( done in 150ms ) 10% initial/edconf [done] ( done in 214ms ) 16% syslogd [started] ( pid: 554 ) 21% klogd [started] ( pid: 558 ) 24% hostname [done] ( done in 267ms ) 29% udev/udevd [started] ( pid: 550 ) 29% NetworkManager/prepare [done] ( done in 316ms ) 32% unionfs [done] ( done in 416ms ) udev/udevd [starting] 32% udev/set_hotplug [done] ( done in 402ms ) udev/udevd [starting] 35% crond [started] ( pid: 566 ) 37% udev/udevd [started] ( pid: 572 ) 40% modules [done] ( done in 3065ms ) 43% udev/filldev [done] ( done in 5234ms ) 48% getty/1 [started] ( pid: 813 ) 51% swap 54% clock [done] 56% sshd/generate_keys [done] 59% mountfs [done] 62% usb [done] 64% mountuserfs [done] ( done in 624ms ) LaCix Linux release 2.2.2 Kernel 2.6.22.7 on an armv5tejl / ttyS0 LaCie-d2 login: 67% bootmisc [done] ( done in 953ms ) 70% dbus [started] ( pid: 885 ) 72% hald [started] ( pid: 886 ) edconfd daemon: Starting edconfd... 75% dhcdbd [started] ( pid: 894 ) 81% fan_controller [started] ( pid: 884 ) 81% edconfd [started] ( pid: 896 ) 83% NetworkManager [started] ( pid: 900 ) 89% http [started] ( pid: 901 ) samba/smbd [starting] samba/nmbd [starting] samba/winbind [starting] 88% samba/smbd [started] ( pid: 937 ) 88% samba/nmbd [started] ( pid: 938 ) 88% samba/winbind [started] ( pid: 939 ) netatalk/atalkd [starting] netatalk/afpd [starting] 86% netatalk/atalkd [started] ( pid: 985 ) 88% netatalk/afpd [started] ( pid: 988 ) proftpd [starting] 91% proftpd [started] ( pid: 1069 ) avahi [starting] 91% avahi [started] ( pid: 1082 ) 93% sshd [started] ( pid: 1072 ) ipconfd [starting] 93% ipconfd [started] ( pid: 1103 ) avahi [stopping] avahi [stopped] ( stopped in 8ms ) 93% avahi [started] ( pid: 1163 ) reload/samba [starting] 94% reload/samba [done] ( done in 162ms ) reload/proftpd [starting] 94% reload/proftpd [done] ( done in 99ms ) edconfd/started [starting] edconfd/started start: Cleaning up wrong running backup jobs: 92% edconfd/started [done] ( done in 20810ms ) 96% snapshot [done] ( done in 115ms ) 98% recovery [done] ( done in 342ms ) 100% runlevel/default [done] ( done in 66776ms ) runlevel "runlevel/default" up in, 322325ms.