====== Honda NTV650 Revere ======

===== In pista con gli Honda Days =====

Honda Days, Autodromo di Vallelunga, 10 maggio 2003. In pista con la vecchia Revere: 12 anni, 116.000 km.

{{.:honda_ntv650:vallelunga.jpg?500|With the Honda NTV650 Revere on the Vallelunga circuit}}

===== Ancora in strada dopo 33 anni e 250.000 km =====

{{.:honda_ntv650:honda-ntv650-revere-passo-stelvio.jpg?500|The Revere on the Stelvio pass in 2024}}

===== Pagine sulla NTV650 Revere =====

  * **[[honda_ntv650_carburetor]]**
  * **[[honda_ntv650_wiring_diagram]]**
  * **[[honda_ntv650_troubleshooting]]**

===== 154.000 km =====

In a cold saturday of february, when the bike was 15 years and 154.000 km old, she didn't start. The spark plugs got wet of gasoline and dirty, I cleaned two of them but it was not sufficient to start the engine again. After some minutes also the battery started going weak. The spark plugs were only 6.000 km old and too much dirty; it was also too much time that the bike did not her 24 km/l any more (just 19). It was evident that some deep maintenace was needed.

Here are some photos of what i found inside the engine. Many carbon deposits on the ceil of the front piston (the rear one was much cleaner): Carbon went wet by the gasoline, detached itself and filled the plug gap, this was the main cause of the engine not starting. Blowing with compressed air into the engine head - after removing both the plugs - may will cleaned the piston a bit, without the need to break the engine apart.

{{.honda_ntv650:piston_ceil.jpg?200}}
{{.honda_ntv650:head.jpg?200}}
{{.honda_ntv650:piston.jpg?200}}

By contrast the wear of the cylinder was very low, after so many kilometers you still see the honing signs!

{{.honda_ntv650:cylinder.jpg?200}}

I took the cylinders to the shop to be bored and honed and I purchased two shining new pistons.

===== Disassembling the engine =====

The main problem was removing the flywheel and the clutch. The workshop manual suggests to use the Honda special tools:

  * 07733-0020001 Rotor puller (Estrattore rotore)
  * 07725-0040000 Flywheel holder (Attrezzo bloccaggio rotore)
  * {{.honda_ntv650:clutch_holder_07923-ke10000.pdf|07923-KE10000 Clutch center holder}} (Attrezzo bloccaggio mozzo frizione)

{{.honda_ntv650:engine.jpg?280}}
{{.honda_ntv650:clutch.jpg?280}}

I purchased the rotor puller on the web from  **SG Motorsport** ([[http://www.inter-bike.co.uk/|www.inter-bike.co.uk]]). They answered kindly and quickly to my email, the shipping is a bit pricey but in 5 days I got it. The clutch holder was made with a lathe by a friend of mine. Here they are two photos of the tools:

{{.honda_ntv650:puller_07733-0020001.jpg?60}}
{{.honda_ntv650:holder_07923-ke10000.jpg?80}}

I ordered all the spare parts from my Honda dealer; I'm still amazed that I can find [[honda_ntv650_parts|every part of the bike]]: pistons, gaskets, bolts, ... down to the smallest washer. All of that more that 10 years that my bike is out of production and despite the fact that this model was not so popular in Italy. This is why I will purchase Honda again!

===== Disegni esplosi e codici dei ricambi =====

Consultate il [[http://naxos.rigacci.org/epc/index.php?cmodnamepc=ntv650|Catalogo EPC]] (HONDA Motorcycle Electronic Parts Catalogue).