Differences

This shows you the differences between two versions of the page.

--- doc:appunti:hardware:freerunner_debian [2011/10/29 21:51] – [The FSO DBus interface] niccolo
+++ doc:appunti:hardware:freerunner_debian [2011/11/01 15:23] (current) – [GSM/GPRS] niccolo
@@ Line 129: / Line 129: @@
     * **fso-deviced-openmoko**
         * **fso-deviced**
+    * **fso-gsmd-openmoko**
+      * **fso-gsmd**
   * **mdbus2**
   * **fsoraw**
@@ Line 162: / Line 164: @@
 </code>
+==== fso-gsmd ====
+The configuration file is:
+  * **''/etc/freesmartphone/conf/<platform>/fsogsmd.conf''** or
+  * **''/etc/freesmartphone/conf/default/fsogsmd.conf''**
+Man page says: //The daemon will be started automatically by DBus, once a request is send to it//; actually the daemon is started just after ''fsodeviced'' is started.
+The ''fsogsmd'' implementation is capable of **{{.:freerunner:0710-720.zip|GSM 07.10 Multiplexing}}** using the library ''libgsm0710mux'', so installing the **fso-abyss** or the previous **fso-gsm0710muxd** packages is not required.
 ===== The Devices =====
@@ Line 175: / Line 187: @@
 ==== GSM/GPRS ====
-Shuld upgrade the GSM modem firmware? Look at this page about **[[http://wiki.openmoko.org/wiki/GSM/Flashing|flashing]]**.
+=== Upgrading the modem firmware ===
-FIXME Check the new **fso-abyss** package which superseed fso-gsm0710muxd, chek what are the proper packages to install:
+I don't need to upgrade the GSM modem firmware (see **[[http://wiki.openmoko.org/wiki/GSM/Flashing|flashing]]**) because Moko11 is the latest version available. Checked with **''minicom''** (''/dev/ttySAC0'', 115200 8N1):
-  * [[http://packages.debian.org/sid/fso-gsmd|fso-gsmd]]
+<code>
-  * [[http://packages.debian.org/sid/fso-abyss|fso-abyss]]
+AT+CGMR
-  * [[http://packages.debian.org/sid/fso-gsm0710muxd|fso-gsm0710muxd]]
++CGMR: "GSM: gsm_ac_gp_fd_pu_em_cph_ds_vc_cal35_ri_36_amd8_ts0-Moko11"
+</code>
-FSO provides a nice multiplexing of GSM/GPRS. Different aplications can talk to the GSM modem concurrently and place GSM calls while running a GPRS internet connection (bandwidth will be the bottleneck!). The GSM multiplexing is handled by the **fso-gsm0710muxd** package.
+=== TCP/IP connection (GPRS) ===
-Clicking on the GSM icon on the panel should allow to start/stop a GPRS connection. Unfortunately **I got several problems maging GPRS calls**, may be simply related to the AT commands used in dialling. I was lazy on debugging, so I resorted on self-made scripts and the traditional **''pon''**/**''poff''** commands. Here it is my ''gprs-on'' script:
+The TCP/IP connection is called GSM PDP (Packet Data Protocol) and it is handled by the FSO stack, the package providing this interface is **fso-gsmd**. The ''fsogsmd'' daemon actually uses **''pppd''** to make the connection and to create the ''ppp0'' interface.
-<code bash>
+''pppd'' is called with some default options (search ''ppp_options'' into the source files), which don't work with the ISP provider I know. Fortunately we can override the options in **''/etc/freesmartphone/conf/GTA02/fsogsmd.conf''**
-#!/bin/sh
-# Don't use GSM multiplexer, talk directlty to the modem.
+<file>
-killall gsm0710muxd
+# Conseder also the options ktune;proxyarp for tethering.
-om gsm power 1
+ppp_options = debug;115200;nodetach;modem;crtscts;hide-password;noauth;noipdefault;defaultroute;replacedefaultroute;usepeerdns;noproxyarp
-poff -a
+</file>
-pon
+=== Missing ppp2fsogsmd.so ===
+There was the [[http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=647078|bug 647078]] which caused this error in ''/var/log/fsogsmd.log'':
+<code>
+[INFO]  PdpPppMux <>: PDP Context Status now FREE_SMARTPHONE_GSM_CONTEXT_STATUS_OUTGOING
+[INFO]  PdpPppMux <>: PDP Context Status now FREE_SMARTPHONE_GSM_CONTEXT_STATUS_RELEASED
+[WARN]  PdpPppMux <>: PPP quit immediately; check options and permissions.
+</code>
+I had to make this symlink:
+<code>
+/usr/lib/cornucopia -> /usr/lib/arm-linux-gnueabi/cornucopia/
 </code>
@@ Line 200: / Line 227: @@
 This is the service provided by the package **fso-gsmd** and the low-level driver **fso-gsmd-openmoko**, which are from FSO Cornucopia implementation.
-Making a TCP/IP connection uses the Packet Data Protocol interface. First of all enter the APN, login and password:
+Making a TCP/IP connection uses the Packet Data Protocol interface. This is an example of DBus chat, using **''mdbus2''** in interactive mode.
+  - The GSM modem gets powered-on with ''RequestResource''.
+  - Register on the GSM network.
+  - APN, login and password are entered.
+  - Check PDP status and start the connection.
 <code>
-mdbus2 -s org.freesmartphone.ogsmd \
+mdbus2 -s -i
-    /org/freesmartphone/GSM/Device \
+MDBUS2> org.freesmartphone.ousaged /org/freesmartphone/Usage org.freesmartphone.Usage.RequestResource GSM
-    org.freesmartphone.GSM.PDP.SetCredentials internet.wind wind wind
+MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.Network.Register
+MDBUS2> org.freesmartphone.ogsmd  /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.SetCredentials internet.wind wind wind
+MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.GetContextStatus
+("released",{})
+MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.ActivateContext
+MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.GetContextStatus
+("active",{})
+MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.DeactivateContext
+MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device  org.freesmartphone.GSM.Network.Unregister
 </code>
-Then check the connection status, place a call and terminate it:
+FIXME: exiting ''mdbus2'' (with Ctrl-D), the GSM device is released (and the power turned off), but ''pppd'' is not terminated, it remains running and consumes the log file.
-<code>
+=== Other notes ===
-mdbus2 -s org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device \
-    org.freesmartphone.GSM.PDP.GetContextStatus
-("released",{})
-... org.freesmartphone.GSM.PDP.ActivateContext
+FIXME The following is old stuff, superceeded by FSO Cornucopia implementation.
-... org.freesmartphone.GSM.PDP.DeactivateContext
+FSO provides a nice multiplexing of GSM/GPRS. Different aplications can talk to the GSM modem concurrently and place GSM calls while running a GPRS internet connection (bandwidth will be the bottleneck!). The GSM multiplexing is handled by the **fso-gsm0710muxd** package.
+Clicking on the GSM icon on the panel should allow to start/stop a GPRS connection. Unfortunately **I got several problems maging GPRS calls**, may be simply related to the AT commands used in dialling. I was lazy on debugging, so I resorted on self-made scripts and the traditional **''pon''**/**''poff''** commands. Here it is my ''gprs-on'' script:
+<code bash>
+#!/bin/sh
+# Don't use GSM multiplexer, talk directlty to the modem.
+killall gsm0710muxd
+om gsm power 1
+poff -a
+pon
 </code>
-The data connection involves running pppd?
 ==== Battery ====
@@ Line 441: / Line 488: @@
 ==== WiFi broken in openmoko-panel-plugin ====
-The **fso-deviced-openmoko** should be patched because the sysfs path to control the WiFi power changed in kernel 2.6.34. See **[[http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=647003|Debian bug #647003]]**.
+The **fso-deviced-openmoko** before 0.9.5+git20110805-2 has a bug (the WiFi power sysfs path changed in kernel 2.6.34), see **[[http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=647003|Debian bug #647003]]**.
 Also **''openmoko-panel-plugin''** must be patched to use the new FSO DBus interface. I will release that patched version soon.
@@ Line 621: / Line 668: @@
 Idle status is one of the following: **''busy''**, **''idle''**, **''idle_dim''**, **''idle_prelock''**, **''lock''** and **''suspend''**. To prevent the device entering a state, set its timeout to **''-1''** (see the note below). If a state is disabled, the subsequent states are never reached.
-**NOTE**: to set a timeout of **''-1''** you cannot use the command line because **''-1''** is interpreted as an option. Use this trick:
+**NOTE**: to set a timeout of **''-1''** you cannot use the command line because **''-1''** is interpreted as an option. We can use the interactive mode of ''mdbus2'' (terminate with Ctrl-D):
+<code>
+mdbus2 -s -i
+MDBUS2> org.freesmartphone.odeviced /org/freesmartphone/Device/IdleNotifier/0 org.freesmartphone.Device.IdleNotifier.SetTimeout idle -1
+</code>
+If you want to use it into a script, just make this:
 <code bash>
+#!/bin/sh
 BUS='org.freesmartphone.odeviced'
 IDLE_SERVICE='/org/freesmartphone/Device/IdleNotifier/0'