Differences

This shows you the differences between two versions of the page.

--- doc:appunti:hardware:freerunner_debian [2011/11/01 07:40] – [fso-gsmd] niccolo
+++ doc:appunti:hardware:freerunner_debian [2011/11/01 07:51] – [GSM/GPRS] niccolo
@@ Line 230: / Line 230: @@
   - The GSM modem gets powered-on with ''RequestResource''.
-  - APN, login and password are entered.
   - Register on the GSM network.
+  - APN, login and password are entered.
   - Check PDP status and start the connection.
@@ Line 237: / Line 237: @@
 mdbus2 -s -i
 MDBUS2> org.freesmartphone.ousaged /org/freesmartphone/Usage org.freesmartphone.Usage.RequestResource GSM
-()
+MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.Network.Register
 MDBUS2> org.freesmartphone.ogsmd  /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.SetCredentials internet.wind wind wind
-()
-MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.Network.Register
-()
 MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.GetContextStatus
 ("released",{})
 MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.ActivateContext
-()
 MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.GetContextStatus
 ("active",{})
 MDBUS2> org.freesmartphone.ogsmd /org/freesmartphone/GSM/Device org.freesmartphone.GSM.PDP.DeactivateContext
-()
 </code>
@@ Line 255: / Line 250: @@
 === Other notes ===
-FIXME Check the new **fso-abyss** package which superseed fso-gsm0710muxd, chek what are the proper packages to install:
-  * [[http://packages.debian.org/sid/fso-gsmd|fso-gsmd]]
-  * [[http://packages.debian.org/sid/fso-abyss|fso-abyss]]
-  * [[http://packages.debian.org/sid/fso-gsm0710muxd|fso-gsm0710muxd]]
 FIXME The following is old stuff, superceeded by FSO Cornucopia implementation.
@@ Line 678: / Line 667: @@
 Idle status is one of the following: **''busy''**, **''idle''**, **''idle_dim''**, **''idle_prelock''**, **''lock''** and **''suspend''**. To prevent the device entering a state, set its timeout to **''-1''** (see the note below). If a state is disabled, the subsequent states are never reached.
-**NOTE**: to set a timeout of **''-1''** you cannot use the command line because **''-1''** is interpreted as an option. Use this trick:
+**NOTE**: to set a timeout of **''-1''** you cannot use the command line because **''-1''** is interpreted as an option. We can use the interactive mode of ''mdbus2'' (terminate with Ctrl-D):
+<code>
+mdbus2 -s -i
+MDBUS2> org.freesmartphone.odeviced /org/freesmartphone/Device/IdleNotifier/0 org.freesmartphone.Device.IdleNotifier.SetTimeout idle -1
+</code>
+If you want to use it into a script, just make this:
 <code bash>
+#!/bin/sh
 BUS='org.freesmartphone.odeviced'
 IDLE_SERVICE='/org/freesmartphone/Device/IdleNotifier/0'