doc:appunti:android:osmand_on_motorbike
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
doc:appunti:android:osmand_on_motorbike [2022/08/08 16:03] – [Using OsmAnd on a motorbike] niccolo | doc:appunti:android:osmand_on_motorbike [2023/09/04 07:34] – [Using OsmAnd on a motorbike] niccolo | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Using OsmAnd on a motorbike ====== | ====== Using OsmAnd on a motorbike ====== | ||
- | In this article I write some notes about using and **Android** device (actually a **smartphone**) as a **GPS navigation system on a motorbike**. The choosen software is **[[https:// | + | In this article I write some notes about using and **Android** device (actually a **smartphone**) as a **GPS navigation system on a motorbike**. The choosen software is **[[https:// |
===== Mounting ===== | ===== Mounting ===== | ||
+ | First of all, it is necessary to make a premise: I usually travel at very low speeds, hardly exceeding **90 km/h**. My bike, despite being a **650 cc twin cylinder**, has few vibrations and I only occasionally drive on dirt roads. Here I tell you what is my setup, which is working well for my needs, but you must adapt the mounting to your specific scenario. | ||
+ | |||
+ | I provided both the smartphones with a **flexible TPU cover**. The ZTE is quite **thin**, so it is blocked firmly by the holder without any additional precautions. Instead the Oukitel is **thick and heavy** enough that the gaff clips on the phone holder do not tighten it sufficiently. | ||
+ | |||
+ | FIXME | ||
===== Waterproof ===== | ===== Waterproof ===== | ||
- | The ZTE is not waterproof, so I can only use it when the weather is nice. Instead the WP12 is rated as **[[wp> | + | The **Blade A610** |
+ | |||
+ | Instead the **WP12** is rated as **[[wp> | ||
+ | |||
+ | {{.: | ||
- | However, the water resistance of the WP12 is ensured by **a rubber plug protecting the power connector**, | ||
===== The charging cable ===== | ===== The charging cable ===== | ||
Line 16: | Line 25: | ||
=== Magnetic connector === | === Magnetic connector === | ||
+ | |||
+ | To keep the ZTE permanently connected to the **charging cable**, I purchased a **micro-USB magnetic adapter** (specifically a **NetDot 10th Gen**). The magnetic adapter is quite convenient to plug/unplug the power connector even wearing gloves and it prevents damages if you inadvertently pull the cable. | ||
+ | |||
+ | {{.: | ||
+ | |||
+ | In the photo above you can see two adapters: one fitted into the phone connector and the one that I carry with me as a **spare part**. I used just a bit of silicone adhesive to make the plug more stable and to prevent dust from entering. It turned out that the magnetic coupling is quite **strong and stable** to resist to vibrations and wind. You must pay attention to avoid dust into the electric contacts, which are rather delicate and can actract **ferromagnetic dust**. | ||
===== Screen brightness ===== | ===== Screen brightness ===== | ||
Line 24: | Line 39: | ||
===== Overheating ===== | ===== Overheating ===== | ||
+ | |||
+ | ===== OsmAnd settings ===== | ||
doc/appunti/android/osmand_on_motorbike.txt · Last modified: 2023/09/04 07:42 by niccolo