doc:appunti:hardware:qnap_ts-120
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
doc:appunti:hardware:qnap_ts-120 [2022/02/11 18:03] – [Console seriale] niccolo | doc:appunti:hardware:qnap_ts-120 [2022/02/12 07:06] (current) – [The Serial Console] niccolo | ||
---|---|---|---|
Line 95: | Line 95: | ||
</ | </ | ||
- | ===== Serial Console ===== | + | ===== The Serial Console ===== |
+ | {{ .: | ||
{{ .: | {{ .: | ||
- | On the circuit board of the QNAP TS-120 there is a JTAG connector for the serial console. I used an old CD-ROM audio cable because it had the right connector. I wired only the **GND**, **TX** and **RX** pins from to QNAP to a serial-to-USB adapter. The adapter was inserted intp a GNU/Linux computer running the **minicom** program. The speed of the serial line was set to **115200**. | + | On the circuit board of the QNAP TS-120 there is a JTAG connector for the serial console. I used an old CD-ROM audio cable because it had the right connector. I wired only the **GND**, **TX** and **RX** pins from to QNAP to a serial-to-USB adapter. The adapter was inserted intp a GNU/Linux computer running the **minicom** program. The speed of the serial line was set to **115200**. The connector pinout is documented in this page: [[http:// |
- | + | ||
- | The connector pinout is (thanks to [[http:// | + | |
+ | ^ Console Pinout | ||
^ 1 | TX | | ^ 1 | TX | | ||
^ 2 | VCC +3.3 | | ^ 2 | VCC +3.3 | | ||
Line 107: | Line 107: | ||
^ 4 | GND | | ^ 4 | GND | | ||
- | {{.:qnap:qnap-ts-120-serial-console-jtag.jpg? | + | This is the boot process captured from the serial line. At the end of the bootstrap you will get a **login prompt**. |
+ | |||
+ | < | ||
+ | | ||
+ | | \/ | __ _ _ ____ | ||
+ | | |\/| |/ _` | '__\ \ / / _ \ | | | ||
+ | | | | | (_| | | \ V / __/ | | | ||
+ | |_| |_|\__, | ||
+ | | ||
+ | | | | | | __ ) ___ ___ | |_ | ||
+ | | | | |___| _ \ / _ \ / _ \| __| | ||
+ | | |_| |___| |_) | (_) | (_) | |_ | ||
+ | | ||
+ | ** MARVELL BOARD: DB-88F6282A-BP LE TS-120 ,PHY=1.8v | ||
+ | |||
+ | U-Boot 1.1.4 (Nov 5 2012 - 17:39:47) Marvell version: 3.5.3 | ||
+ | U-Boot code: 00600000 -> 0067FFF0 | ||
+ | Soc: MV88F6282 Rev 1CPU running @ 1600Mhz L2 running @ 533Mhz | ||
+ | SysClock = 533Mhz , TClock = 200Mhz | ||
+ | </ | ||
===== Real Time Clock rtc0 ===== | ===== Real Time Clock rtc0 ===== | ||
doc/appunti/hardware/qnap_ts-120.txt · Last modified: 2022/02/12 07:06 by niccolo